The Zenith 2 clearomizer, improved version of the Zenith Pro clearomizer

While the Zenith Pro is already a success, Innokin repeats and launches its new little gem in partnership with reviewers Phil Busardo and Dimitri Agrafiotis, the Zenith 2 clearomizer. Wider than its predecessor, it has a 26mm diameter, 2mm more than the previous one and a tank that can accommodate up to 5.5mlof your favorite liquid. With an improved top fill and a choice of drip 510 (MTL and DL), what more could you want?

Zenith 2 Tank Performance

Versatile as desired, the Zenith 2 allows both a direct inhalation vape (RDL) and an indirect inhalation vape (MTL). An airflow ring located at the base of the clearomizer(bottom airflow) will allow you to adjust your draw very simply. Three small airflow holes for a restrictive draw and a considerable slot for a more airy draw, it's up to you. In terms of design, the Zenith 2 is very similar to its predecessor, the Zenith Pro, but with a more cut and polished look

The Zenith 2 is delivered with 2 Zenith resistors

- Zenith resistor (Z-coil) of 0.8 ohm (pre-installed): versatile vape - to use between 15 and 18W - ratio 40PG/60VG or 70PG/30VG

- Zenith resistor (Z-Coil) of 0.3 ohm: aerial vape DL - to use between 30 and 40W - ratio 50PG/50VG or 30PG/70VG

An ultra versatile vape for indirect (MTL) or direct (RDL) inhalation. The Zenith 2 tank is compatible with Zenith resistances (Z-coil) of Innokin (sold separately) :

- Zenith Z-Plex3D resistor of 0.48 ohm (mesh) : tasty MTL tight vape with excellent longevity - to be used between 13 and 16 W - ratio 40PG/60VG or 70PG/30VG

- Zenith Z Plexus resistor of 0.5 Ohm (kanthal A1) Z-coil : MTL tight vape between steam and flavors - to be used between 14 and 19 W - ratio 40PG/60VG or 70PG/30VG

- Zenith Z 1 ohm resistor RDL semi aerial vape - use between 20 and 25 W - ratio 50PG/50VG or 70PG/30VG

- Zenith 1.2 ohm resistor (kanthal A1) MTL - to use between 10 and 14 W - ratio 50PG/50VG or 70PG/30VG - compatible with high nicotine rate and nicotine salts

- Zenith resistance of 1.60 ohm (kanthal A1) Very tight MTL vape - use between 10 and 14 W - ratio 50PG/50VG or 70PG/30VG - compatible with high nicotine rate and nicotine salts

The ease of use of clearomizer Zenith 2 Innokin

This clearomizer is very easy to use and these few improvements will greatly facilitate your life. Level filling, the Zenith 2 has a sliding system of the top-cap to access the hole, sealing guaranteed! Thanks to its silicone membrane, filling your clearomizer will be fast and especially clean

Regarding the change of resistance, you will simply unscrew the base of your clearomizer, remove the damaged resistance and push the new resistance inside by matching the edges

Warning: For each change of resistance it is important to soak the cotton with a drop of eliquid and let it act a few minutes for a longer life and avoid any risk of burning the new resistance

With which equipment to use the Innokin Zenith 2 clearomizer?

The Zenith 2 clearomizer can be used with the brand new Coolfire Z80 box from Innokin. As versatile as the Zenith 2 clearomizer, it will allow you to reach a power of 80W. This box is also compatible with almost all clearomizers on the market. The combination of these two materials is now available with the Coolfire Z80 kit that you will find in associated product

The clearomizer Zenith 2 Innokin comes with :

- 1 Zenith 2 tank

- 1 Zenith resistance (Z-coil) of 0.80 ohm

- 1 Zenith resistance (Z-coil) of 0.30 ohm

- 2 Drip Tips (MTL and DL)

- O'Rings

- 1 user manual

Characteristics of the Zenith 2 tank from Innokin

- Dimensions : 51,7 mm x 26 mm

- Weight : 61g